Unlock K1/Z3 without TP

[Clarkey]

Try disabling your antivirus beofre you run it/

[supersk]

i have tried disabling my anti-virus. no luck. after viewing some of the posts in this thread, some users have mentioned that you need windows xp with sp1 or below. is this true?

[Clarkey]

I'm using XP SP2 on my laptop and SP3 on my PC and it works fine for me

[supersk]

does it use any of the .NET frameworks?

i've installed 1.1, 2, and 3.5 with all service packs. maybe I have to uninstall them?

okay, i just tried installing ms tool on a different computer that is windows xp sp1 and it has the same problem.

maybe for some reason i downloaded bad ms tool file from different sources...as unlikely as that seems.

i don't know. i am trying to install ms tool 8r.

[SocaSlvr]

no installation is required
make sure you have the load it file and are using that to open it
search 4shared for it
--
btw it was me that said i had to go back to sp1, but that was only because my comp was messed up and i also had avg (mstool doesnt like this)
but mstool works on sp1 sp2 and sp3

[supersk]

Thanks SocaSlvr. I have completed the unlock process successfully. very cool.

But for some reason, I can't re-enter a new Security Code. I'm trying to do a Master Reset but I don't have the Old Security Code.

I've tried entering 0000 and 1234 and the last 4 digits of my current cell phone number without success.

Question: does the unlock procedure reset the security code?

[SocaSlvr]

use p2k advanced editor to read it
or just flash an UNLOCKED stock mp and it will be set to zero's

[tonyg_253]

Just FYI, i succesfully unlocked a K1 0A.B2 using this thread. However MStool would not work under vista, had to use xp and it worked like a charm.
Thanks
TonyG

[supersk]

thanks again! this worked. phone is now unlocked.

[vicky_gill]

Original Thread on MotoX

This guide was just re-translated and posted on m3 by me, The works here are still of the Original Poster.

You will need: -
MS Tool (Google it, it's warez)
K1/Z3 boot core( I will put a download link up shortly)

Here are the quick steps for this tutorial.

1. Open up MS tool and select your phone profile (K1 or Z3.
2. Connect phone in bootloader mode usiung the *+# + power on method
3. Select "Read backup" and choose PDS
*Note if your phone gets a critical error message here please do not use the rest of this tutorial.

If the backup was done without any error this means that the phone is compatible with the tutorial as mstool can read data from the RAMDLD and can write the bootloader and read the PDS!

Now only proceed if everything is okay: battery fully charged without sim card and memory card.


Let's continue :-

4. Conect phone in bootloader mode "*" + "#" + "power";
5. Open mstool and click in "Write Backup"
6. Select the file "K1__BOOTCORE_TP.bkp" for K1 or "Z3__BOOTCORE_TP.bkp" for Z3;
7. OK. After your phone shuts down automatically, remove the battery and replace the battery. The phone will be recognized by the PC. To see if everything is okay, open RSDLite and make sure it detected "S BLANK NEPTUNE LTE2"... If it is, everything is ok! The phone screen is black! This is OK.
8. Now open mstool and click "unlock". Wait for the phone being disconnected, remove the battery and replace the battery again;
9. In mstool click "Write Backup";
10. Select bootloader 0A.B2 for k1 and 0A.C0 for Z3;
Enjoy!

Download the files here

i m trying to connect moto k1 with ms tool software ,,but it cudn't .it easliy connect with other software like rsd lite etc...
i hv the following
BOOT LOADER
0D.C0
SW Version:
R47121_G_08.01.11R
Trk1Chrg:Enbld

[SocaSlvr]

R47121 firmware is problems
you have to hard test point to get blank

[vicky_gill]

Original Thread on MotoX

This guide was just re-translated and posted on m3 by me, The works here are still of the Original Poster.

You will need: -
MS Tool (Google it, it's warez)
K1/Z3 boot core( I will put a download link up shortly)

Here are the quick steps for this tutorial.

1. Open up MS tool and select your phone profile (K1 or Z3.
2. Connect phone in bootloader mode usiung the *+# + power on method
3. Select "Read backup" and choose PDS
*Note if your phone gets a critical error message here please do not use the rest of this tutorial.

If the backup was done without any error this means that the phone is compatible with the tutorial as mstool can read data from the RAMDLD and can write the bootloader and read the PDS!

Now only proceed if everything is okay: battery fully charged without sim card and memory card.


Let's continue :-

4. Conect phone in bootloader mode "*" + "#" + "power";
5. Open mstool and click in "Write Backup"
6. Select the file "K1__BOOTCORE_TP.bkp" for K1 or "Z3__BOOTCORE_TP.bkp" for Z3;
7. OK. After your phone shuts down automatically, remove the battery and replace the battery. The phone will be recognized by the PC. To see if everything is okay, open RSDLite and make sure it detected "S BLANK NEPTUNE LTE2"... If it is, everything is ok! The phone screen is black! This is OK.
8. Now open mstool and click "unlock". Wait for the phone being disconnected, remove the battery and replace the battery again;
9. In mstool click "Write Backup";
10. Select bootloader 0A.B2 for k1 and 0A.C0 for Z3;
Enjoy!

Download the files here

can u explain is it the same way of bootloader mode as *# red button

R47121 firmware is problems
you have to hard test point to get blank

can u send me the link ..how can i do hard test poit

[Trickybitch]

Testpoint guide:
http://modmymoto.com/wiki/index.php/KRZR_K1_Testpoint

[Cursedfungus]

I tried this and now I have a PH Sig err 39:02:
I've had so many of those it isn't funny. I have a z3 and I don't know what I did wrong.

[MotoMudder]

well theres a guide in the Z3 bible for PH Sig err. but I suggest just TPing and removing RSA, which is also in the bible.