ok so here, im not a newb, but im not an expert either, i have a V3R, from "Rogers" canadian gsm provider. it is sim locked, and i have flashed a mp to it, i used nightfall's 4515 mp pack, here is my relevant V3R info...
-- Boot Loader Screen --
OK to Program
-- END Boot Loader Screen --
-- Other Information Screen --
-- END Other Information Screen --
Now... will this info from this post work on my phone, or no, it seems it has worked for a few, but were they versions other than mine, or were some of them 4515's?? not sure if process might be different or not??,, if it is, has anyone done a 100% success on a 4515 v3r? any help or additional info would be so helpful. im a fido customer who got this phone for free and want to use it on rogers
( Quote )" Originally Posted by ray 2x View Post
hey guys, sorry to take so long to reply to my own thread lol! anyways the reason i didnt reply is because i solved the problem the same day i had the problem, with p2k easy tools 3.9 (cracked) you can unlock your v3r very easy with test point. first connect phone, then connect test point, then connect battery,then click on "do selected job", then disconnect test point (as directed to by easy tools), let easy tools do its thing...... and done your phone is now unlocked however it wont start up! sooo..... click on repair tab, then check "full repair with PDS checksum...... blah blah", then connect phone to computer again, then connect test point (yup one more time), then connect battery, then click on "do selected job"! let easy tools do its thing..... and BAM all done, phone unlocked and fully functionable.
i have now unlocked 2 v3r's this way with no problems. good luck and it never hurts to back-up your phone! "( END Quote )
i wanted to confirm if the method used by ray 2x to unlock his v3r would work on mine, its a 4515 firmware not the 3443... so i was curious as to if it would work or not, and if anyone else was successful in doing this method, as this is my only phone, i dont need to have a brick, but i have both fido and rogers accounts, and only one phone, rogers is for work, fido is for personal, so when im not at work, i dont want to run my bill on the rogers., id rather use my pay as u go fido chip,
any info would be greatful
I have a r4515 myself and going by some who have tried, p2k easy tools can be a brick maker with it. There are some info about a newer version then 3.9, and there was some success, without any risk would be an IMEI service which works oput your subsidy code, they are not to expensive but can't give a guarantee either. but they don't brick things, lol. I dot know how much rogers would charge you for the code if you were going abroad fpr example, find out.
ok so i been doin hella research on how to unlock the damn v3r and finaly felt confident enough to go ahead and give it a try. well..... i did the testpoint thing and used easy tool 39 and it seemed everything went well, easy tool didnt say any errors and said unlock successful and finished-phone reboting. now when it rebooted first the key pad lit up and then the hello moto start screen apeared but then it just turned off? and now thats what happens everytime i turn it on??? i can still connect it to the computer in flash mode (*+#+power) and all my programs will still read it like rsd lite and so on..... but im stuck? i aint got a clue on what i should do?? so if anyone thinks they can help me out that'd be waaaay cool.
oh and i checked the pds or what ever with fb3 and it confirms that its now unlocked...... FFFF < means unlocked, i think!
i do have also the same problem...
i have successfully unlock my v3r bootloader 0a.52..
but when i try to repair PDS, it didnt go correctly.
my phone starts up with the moto the blue one then shut down.
any solution plz?
you need to do PDS repair again. make sure you do the Testpoint properly. i like to run RSDlite before performing the TP, this way when it shows up in RSDlite as s-Blank Neptune LTE2 i know to remove the TP wire. if it remains in RSDlite at this point, you have made a proper TP. Now go into p2k easy tools and select the PDS repair feature.