[pensacol]

I was trying to upload a drm to my v3xx MLD (it was the zero mld drm) and loaded it in fnb. When I hit write data, it went through the erasing process. DONE. Then on uploading code group CG1 it locked up. Wouldn't do anything at all. I had no choice but to remove the battery. Now it's stuck in bootloader. I have a complete backup in fnb, and also a mld monster pack. Both RSD lite, and fnb lock up on the same code group. I cannot upload anything the phone. Does anybody have any suggestions on how I can reflash the phone?

UPDATE: I can write code group CG2 (flex) but not CG1 (firmware). This is from the original backup I made.

[avatar_43]

Just flash the flex drm etc, No need for the firmware really

[pensacol]

Ok, I gotta stop I am not very good at this. Gotta new v3xx since old one broke. Same phone, same firmware, everything. Tried to flash the zero drm again, same thing. Man I'm P.O.ed Stuck in bootloader again. Only certain parts of the backup will flash, and that's only sometimes. Sometimes they will flash correctly, but most they will lock up. Can't flash the flex. Phone said Mem_map empty, but RSD says S Flash Argon. Can't flash from there either. Last time I was able to just flash the stock flex, and them it took everything else, but this one will sometimes start to flash the flex and lock up, and sometimes it won't start flashing it at all. I just got this phone a couple hours ago. I wish I could just leave well enough alone. Somebody please give me some suggestions.

Thanks.

[Cyberwulf]

It may be the same model, but I bet you had another firmware. Sounds like you might have bricked it. Did you make a back up of the NEW phone before you flashed? You may be able to flash back to that to get a working phone.

[pensacol]

Of course not! But the backup I have from my old phone is exactly the same. Same firmware, same flex versions. I can flash the digital signatures fine. But sometime it will lock up at 3% sometimes won't start at all sending CG2. I have also tried every MLD MP that was on this site and everythings the same.

[bassix]

Same problem here! RSD Lite and P2kToolsVS freezes when attempting to load CG1.
I get an error code on the phone (DEA1), and in RSD Lite I get "Error flashing subscriber unit. Device API Error: 0xE0030007 Address: 0xA6D8000...".

I copied ALL of the system files and anything else I could get access to manually... from the phone in P2kC to my hard drive before flashing. Can I restore from P2kC? RSD Lite 3.9 / 4.1 wouldn't backup when I treid several times.

On an AT&T/Cingular MLD version, just like pensacol

Please Help!

Thank you!

[Kameirus]

try using a different usb port

[bassix]

I did already try different USB ports. Do you think it's the drivers? It seems that IF it were the 3.5.0 drivers, then if there was a problem...the phone would not be recognized at all.

[Kameirus]

try uninstalling the usb drivers then reinstalling them then try using a different usb port that you had first used then connect your phone and let it do the driver installs
i think there is 2 or 3 of them
also maybe try another usb cable if you have one

[pensacol]

I GOT IT!!! After a day and a half of trying to flash this darn thing I finally said what the hell and tried it on my laptop. Worked on the first try! I even uploaded the DRM with no problems. Must have just not liked my USB ports. I tried deleting and reinstalling drivers, a different port, everything. It even charged from the usb port in my laptop which I could never get it to do in my computer.

[bassix]

Congrats!

Questions: Which MP did you use?

Kamierus, I notice in your signature that you have the "Flashed to AT&T..R26111LD-AS_U_96.B0.0AR USIZRGBLATTUSAR26111019"

I'm trying to get the MLD version back in, but the MP that I have is AT&T..R26111MLD-AS_U_96.B0.0FR USIZRGBLATTUSAR26111019.
Is there an MLD version that is "0AR"? (R26111MLD-AS_U_96.B0.0AR USIZRGBLATTUSAR26111019)

Thanks!
MB

[pensacol]

I used the 0AR. I found the stock one on the internet. I'll upload it to rapidshare if you want. The 0FR is just an updated firmware, but I would start by flashing the stock.

[bassix]

Yes! PLEASE send me a link for the OAR version!

I'll PM you with my email.

Thank you so much!
bassix

[pensacol]

Ok man, I'm uploading it now. Should be done in about 10 minutes. I will send you the link.

Figured I'd post it here incase somebody else needs it also. This is stock ATT MLD.

AT&T.R26111MLD-AS_U_96.B0.0AR USIZRGBLATTUSAR26111019

http://www.adrive.com/public/a9aad42...d8a2b98e5.html

[bassix]

Thanks for posting the stock AT&T "OAR" file!