Code:
/* arch/arm/mach-msm/acpuclock.c
*
* MSM architecture clock driver
*
* Copyright (C) 2007 Google, Inc.
* Copyright (c) 2007-2009, Code Aurora Forum. All rights reserved.
* Author: San Mehat <san[MENTION=82472]android[/MENTION].com>
*
* This software is licensed under the terms of the GNU General Public
* License version 2, as published by the Free Software Foundation, and
* may be copied, distributed, and modified under those terms.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
*/
#include <linux/version.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/errno.h>
#include <linux/string.h>
#include <linux/delay.h>
#include <linux/clk.h>
#include <linux/cpufreq.h>
#include <linux/mutex.h>
#include <linux/io.h>
#include <linux/sort.h>
#include <linux/remote_spinlock.h>
#include <mach/board.h>
#include <mach/msm_iomap.h>
#include <asm/mach-types.h>
#include "proc_comm.h"
#include "smd_private.h"
#include "clock.h"
#include "acpuclock.h"
#include "socinfo.h"
#define PERF_SWITCH_DEBUG 0
#define PERF_SWITCH_STEP_DEBUG 0
struct clock_state
{
struct clkctl_acpu_speed *current_speed;
struct mutex lock;
uint32_t acpu_switch_time_us;
uint32_t max_speed_delta_khz;
uint32_t vdd_switch_time_us;
unsigned long power_collapse_khz;
unsigned long wait_for_irq_khz;
unsigned long max_axi_khz;
**;
#define PLL_BASE 7
struct shared_pll_control {
uint32_t version;
struct {
/* Denotes if the PLL is ON. Technically, this can be read
* directly from the PLL registers, but this feild is here,
* so let's use it.
*/
uint32_t on;
/* One bit for each processor core. The application processor
* is allocated bit position 1. All other bits should be
* considered as votes from other processors.
*/
uint32_t votes;
** pll[PLL_BASE + ACPU_PLL_END];
**;
struct clkctl_acpu_speed {
unsigned int use_for_scaling;
unsigned int a11clk_khz;
int pll;
unsigned int a11clk_src_sel;
unsigned int a11clk_src_div;
unsigned int ahbclk_khz;
unsigned int ahbclk_div;
int vdd;
unsigned int axiclk_khz;
unsigned long lpj; /* loops_per_jiffy */
/* Pointers in acpu_freq_tbl[] for max up/down steppings. */
struct clkctl_acpu_speed *down[3];
struct clkctl_acpu_speed *up[3];
**;
static remote_spinlock_t pll_lock;
static struct shared_pll_control *pll_control;
static struct clock_state drv_state = { 0 **;
static struct clkctl_acpu_speed *acpu_freq_tbl;
static void __init acpuclk_init(void);
/*
* ACPU freq tables used for different PLLs frequency combinations. The
* correct table is selected during init.
*
* Table stepping up/down entries are calculated during boot to choose the
* largest frequency jump that's less than max_speed_delta_khz on each PLL.
*/
/* 7x01/7x25 normal with GSM capable modem */
static struct clkctl_acpu_speed pll0_245_pll1_768_pll2_1056[] = {
{ 0, 19200, ACPU_PLL_TCXO, 0, 0, 19200, 0, 0, 30720 **,
{ 1, 122880, ACPU_PLL_0, 4, 1, 61440, 1, 3, 61440 **,
{ 0, 128000, ACPU_PLL_1, 1, 5, 64000, 1, 3, 61440 **,
{ 0, 176000, ACPU_PLL_2, 2, 5, 88000, 1, 3, 61440 **,
{ 1, 245760, ACPU_PLL_0, 4, 0, 81920, 2, 4, 61440 **,
{ 1, 256000, ACPU_PLL_1, 1, 2, 128000, 1, 5, 128000 **,
{ 0, 352000, ACPU_PLL_2, 2, 2, 88000, 3, 5, 128000 **,
{ 1, 384000, ACPU_PLL_1, 1, 1, 128000, 2, 6, 128000 **,
{ 1, 600000, ACPU_PLL_2, 2, 1, 200000, 2, 7, 122880 **,
{ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, {0, 0, 0**, {0, 0, 0** **
**;
/* 7x01/7x25 normal with CDMA-only modem */
static struct clkctl_acpu_speed pll0_196_pll1_768_pll2_1056[] = {
{ 0, 19200, ACPU_PLL_TCXO, 0, 0, 19200, 0, 0, 24576 **,
{ 1, 98304, ACPU_PLL_0, 4, 1, 49152, 1, 3, 24576 **,
{ 0, 128000, ACPU_PLL_1, 1, 5, 64000, 1, 3, 24576 **,
{ 0, 176000, ACPU_PLL_2, 2, 5, 88000, 1, 3, 24576 **,
{ 1, 196608, ACPU_PLL_0, 4, 0, 65536, 2, 4, 24576 **,
{ 1, 256000, ACPU_PLL_1, 1, 2, 128000, 1, 5, 128000 **,
{ 0, 352000, ACPU_PLL_2, 2, 2, 88000, 3, 5, 128000 **,
{ 1, 384000, ACPU_PLL_1, 1, 1, 128000, 2, 6, 128000 **,
{ 1, 600000, ACPU_PLL_2, 2, 1, 200000, 2, 7, 122880 **,
{ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, {0, 0, 0**, {0, 0, 0** **
**;
/* 7x01/7x25 turbo with GSM capable modem */
static struct clkctl_acpu_speed pll0_245_pll1_960_pll2_1056[] = {
{ 0, 19200, ACPU_PLL_TCXO, 0, 0, 19200, 0, 0, 30720 **,
{ 0, 120000, ACPU_PLL_1, 1, 7, 60000, 1, 3, 61440 **,
{ 1, 122880, ACPU_PLL_0, 4, 1, 61440, 1, 3, 61440 **,
{ 0, 176000, ACPU_PLL_2, 2, 5, 88000, 1, 3, 61440 **,
{ 1, 245760, ACPU_PLL_0, 4, 0, 81920, 2, 4, 61440 **,
{ 1, 320000, ACPU_PLL_1, 1, 2, 107000, 2, 5, 120000 **,
{ 0, 352000, ACPU_PLL_2, 2, 2, 88000, 3, 5, 120000 **,
{ 1, 480000, ACPU_PLL_1, 1, 1, 120000, 3, 6, 120000 **,
{ 1, 600000, ACPU_PLL_2, 2, 1, 200000, 2, 7, 122880 **,
{ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, {0, 0, 0**, {0, 0, 0** **
**;
/* 7x01/7x25 turbo with CDMA-only modem */
static struct clkctl_acpu_speed pll0_196_pll1_960_pll2_1056[] = {
{ 0, 19200, ACPU_PLL_TCXO, 0, 0, 19200, 0, 0, 24576 **,
{ 1, 98304, ACPU_PLL_0, 4, 1, 49152, 1, 3, 24576 **,
{ 0, 120000, ACPU_PLL_1, 1, 7, 60000, 1, 3, 24576 **,
{ 0, 176000, ACPU_PLL_2, 2, 5, 88000, 1, 3, 24576 **,
{ 1, 196608, ACPU_PLL_0, 4, 0, 65536, 2, 4, 24576 **,
{ 1, 320000, ACPU_PLL_1, 1, 2, 107000, 2, 5, 120000 **,
{ 0, 352000, ACPU_PLL_2, 2, 2, 88000, 3, 5, 120000 **,
{ 1, 480000, ACPU_PLL_1, 1, 1, 120000, 3, 6, 120000 **,
{ 1, 600000, ACPU_PLL_2, 2, 1, 200000, 2, 7, 122880 **,
{ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, {0, 0, 0**, {0, 0, 0** **
**;
/* 7x27 normal with GSM capable modem */
static struct clkctl_acpu_speed pll0_245_pll1_960_pll2_1200[] = {
{ 0, 19200, ACPU_PLL_TCXO, 0, 0, 19200, 0, 0, 30720 **,
{ 0, 120000, ACPU_PLL_1, 1, 7, 60000, 1, 3, 61440 **,
{ 1, 122880, ACPU_PLL_0, 4, 1, 61440, 1, 3, 61440 **,
{ 0, 200000, ACPU_PLL_2, 2, 5, 66667, 2, 4, 61440 **,
{ 1, 245760, ACPU_PLL_0, 4, 0, 122880, 1, 4, 61440 **,
{ 1, 320000, ACPU_PLL_1, 1, 2, 160000, 1, 5, 122880 **,
{ 0, 400000, ACPU_PLL_2, 2, 2, 133333, 2, 5, 122880 **,
{ 1, 480000, ACPU_PLL_1, 1, 1, 160000, 2, 6, 122880 **,
{ 1, 600000, ACPU_PLL_2, 2, 1, 200000, 2, 7, 122880 **,
{ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, {0, 0, 0**, {0, 0, 0** **
**;
/* 7x27 normal with CDMA-only modem */
static struct clkctl_acpu_speed pll0_196_pll1_960_pll2_1200[] = {
{ 0, 19200, ACPU_PLL_TCXO, 0, 0, 19200, 0, 0, 24576 **,
{ 1, 98304, ACPU_PLL_0, 4, 1, 98304, 0, 3, 49152 **,
{ 0, 120000, ACPU_PLL_1, 1, 7, 60000, 1, 3, 49152 **,
{ 1, 196608, ACPU_PLL_0, 4, 0, 65536, 2, 4, 98304 **,
{ 0, 200000, ACPU_PLL_2, 2, 5, 66667, 2, 4, 98304 **,
{ 1, 320000, ACPU_PLL_1, 1, 2, 160000, 1, 5, 120000 **,
{ 0, 400000, ACPU_PLL_2, 2, 2, 133333, 2, 5, 120000 **,
{ 1, 480000, ACPU_PLL_1, 1, 1, 160000, 2, 6, 120000 **,
{ 1, 600000, ACPU_PLL_2, 2, 1, 200000, 2, 7, 120000 **,
{ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, {0, 0, 0**, {0, 0, 0** **
**;
/* 7x27 normal with GSM capable modem - PLL0 and PLL1 swapped */
static struct clkctl_acpu_speed pll0_960_pll1_245_pll2_1200[] = {
{ 0, 19200, ACPU_PLL_TCXO, 0, 0, 19200, 0, 0, 30720 **,
{ 0, 120000, ACPU_PLL_0, 4, 7, 60000, 1, 3, 61440 **,
{ 1, 122880, ACPU_PLL_1, 1, 1, 61440, 1, 3, 61440 **,
{ 0, 200000, ACPU_PLL_2, 2, 5, 66667, 2, 4, 61440 **,
{ 1, 245760, ACPU_PLL_1, 1, 0, 122880, 1, 4, 61440 **,
{ 1, 320000, ACPU_PLL_0, 4, 2, 160000, 1, 5, 122880 **,
{ 0, 400000, ACPU_PLL_2, 2, 2, 133333, 2, 5, 122880 **,
{ 1, 480000, ACPU_PLL_0, 4, 1, 160000, 2, 6, 122880 **,
{ 1, 600000, ACPU_PLL_2, 2, 1, 200000, 2, 7, 122880 **,
{ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, {0, 0, 0**, {0, 0, 0** **
**;
/* 7x27 normal with CDMA-only modem - PLL0 and PLL1 swapped */
static struct clkctl_acpu_speed pll0_960_pll1_196_pll2_1200[] = {
{ 0, 19200, ACPU_PLL_TCXO, 0, 0, 19200, 0, 0, 24576 **,
{ 1, 98304, ACPU_PLL_1, 1, 1, 98304, 0, 3, 49152 **,
{ 0, 120000, ACPU_PLL_0, 4, 7, 60000, 1, 3, 49152 **,
{ 1, 196608, ACPU_PLL_1, 1, 0, 65536, 2, 4, 98304 **,
{ 0, 200000, ACPU_PLL_2, 2, 5, 66667, 2, 4, 98304 **,
{ 1, 320000, ACPU_PLL_0, 4, 2, 160000, 1, 5, 120000 **,
{ 0, 400000, ACPU_PLL_2, 2, 2, 133333, 2, 5, 120000 **,
{ 1, 480000, ACPU_PLL_0, 4, 1, 160000, 2, 6, 120000 **,
{ 1, 600000, ACPU_PLL_2, 2, 1, 200000, 2, 7, 120000 **,
{ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, {0, 0, 0**, {0, 0, 0** **
**;
#define PLL_196_MHZ 10
#define PLL_245_MHZ 12
#define PLL_491_MHZ 25
#define PLL_768_MHZ 40
#define PLL_960_MHZ 50
#define PLL_1056_MHZ 55
#define PLL_1200_MHZ 62
#define PLL_CONFIG(m0, m1, m2) {
PLL_##m0##_MHZ, PLL_##m1##_MHZ, PLL_##m2##_MHZ,
pll0_##m0##_pll1_##m1##_pll2_##m2
**
struct pll_freq_tbl_map {
unsigned int pll0_l;
unsigned int pll1_l;
unsigned int pll2_l;
struct clkctl_acpu_speed *tbl;
**;
static struct pll_freq_tbl_map acpu_freq_tbl_list[] = {
PLL_CONFIG(196, 768, 1056),
PLL_CONFIG(245, 768, 1056),
PLL_CONFIG(196, 960, 1056),
PLL_CONFIG(245, 960, 1056),
PLL_CONFIG(196, 960, 1200),
PLL_CONFIG(245, 960, 1200),
PLL_CONFIG(960, 196, 1200),
PLL_CONFIG(960, 245, 1200),
{ 0, 0, 0, 0 **
**;
#ifdef CONFIG_CPU_FREQ_MSM
static struct cpufreq_frequency_table freq_table[20];
static void __init cpufreq_table_init(void)
{
unsigned int i;
unsigned int freq_cnt = 0;
/* Construct the freq_table table from acpu_freq_tbl since the
* freq_table values need to match frequencies specified in
* acpu_freq_tbl and acpu_freq_tbl needs to be fixed up during init.
*/
for (i = 0; acpu_freq_tbl[i].a11clk_khz != 0
&& freq_cnt < ARRAY_SIZE(freq_table)-1; i++) {
if (acpu_freq_tbl[i].use_for_scaling) {
freq_table[freq_cnt].index = freq_cnt;
freq_table[freq_cnt].frequency
= acpu_freq_tbl[i].a11clk_khz;
freq_cnt++;
**
**
/* freq_table not big enough to store all usable freqs. */
BUG_ON(acpu_freq_tbl[i].a11clk_khz != 0);
freq_table[freq_cnt].index = freq_cnt;
freq_table[freq_cnt].frequency = CPUFREQ_TABLE_END;
pr_info("%d scaling frequencies supported.n", freq_cnt);
**
#endif
unsigned long clk_get_max_axi_khz(void)
{
return drv_state.max_axi_khz;
**
EXPORT_SYMBOL(clk_get_max_axi_khz);
static int pc_pll_request(unsigned id, unsigned on)
{
int res = 0;
on = !!on;
#if PERF_SWITCH_DEBUG
if (on)
printk(KERN_DEBUG "Enabling PLL %dn", id);
else
printk(KERN_DEBUG "Disabling PLL %dn", id);
#endif
if (id >= ACPU_PLL_END)
return -EINVAL;
if (pll_control) {
remote_spin_lock(&pll_lock);
if (on) {
pll_control->pll[PLL_BASE + id].votes |= 2;
if (!pll_control->pll[PLL_BASE + id].on) {
writel(6, PLLn_MODE(id));
udelay(50);
writel(7, PLLn_MODE(id));
pll_control->pll[PLL_BASE + id].on = 1;
**
** else {
pll_control->pll[PLL_BASE + id].votes &= ~2;
if (pll_control->pll[PLL_BASE + id].on
&& !pll_control->pll[PLL_BASE + id].votes) {
writel(0, PLLn_MODE(id));
pll_control->pll[PLL_BASE + id].on = 0;
**
**
remote_spin_unlock(&pll_lock);
** else {
res = msm_proc_comm(PCOM_CLKCTL_RPC_PLL_REQUEST, &id, &on);
if (res < 0)
return res;
else if ((int) id < 0)
return -EINVAL;
**
#if PERF_SWITCH_DEBUG
if (on)
printk(KERN_DEBUG "PLL enabledn");
else
printk(KERN_DEBUG "PLL disabledn");
#endif
return res;
**
/*----------------------------------------------------------------------------
* ARM11 'owned' clock control
*---------------------------------------------------------------------------*/
unsigned long acpuclk_power_collapse(void) {
int ret = acpuclk_get_rate();
acpuclk_set_rate(drv_state.power_collapse_khz, SETRATE_PC);
return ret * 1000;
**
unsigned long acpuclk_wait_for_irq(void) {
int ret = acpuclk_get_rate();
acpuclk_set_rate(drv_state.wait_for_irq_khz, SETRATE_SWFI);
return ret * 1000;
**
static int acpuclk_set_vdd_level(int vdd)
{
uint32_t current_vdd;
current_vdd = readl(A11S_VDD_SVS_PLEVEL_ADDR) & 0x07;
#if PERF_SWITCH_DEBUG
printk(KERN_DEBUG "acpuclock: Switching VDD from %u -> %dn",
current_vdd, vdd);
#endif
writel((1 << 7) | (vdd << 3), A11S_VDD_SVS_PLEVEL_ADDR);
udelay(drv_state.vdd_switch_time_us);
if ((readl(A11S_VDD_SVS_PLEVEL_ADDR) & 0x7) != vdd) {
#if PERF_SWITCH_DEBUG
printk(KERN_ERR "acpuclock: VDD set failedn");
#endif
return -EIO;
**
#if PERF_SWITCH_DEBUG
printk(KERN_DEBUG "acpuclock: VDD switchedn");
#endif
return 0;
**
/* Set proper dividers for the given clock speed. */
static void acpuclk_set_div(const struct clkctl_acpu_speed *hunt_s) {
uint32_t reg_clkctl, reg_clksel, clk_div, src_sel;
reg_clksel = readl(A11S_CLK_SEL_ADDR);
/* AHB_CLK_DIV */
clk_div = (reg_clksel >> 1) & 0x03;
/* CLK_SEL_SRC1NO */
src_sel = reg_clksel & 1;
/*
* If the new clock divider is higher than the previous, then
* program the divider before switching the clock
*/
if (hunt_s->ahbclk_div > clk_div) {
reg_clksel &= ~(0x3 << 1);
reg_clksel |= (hunt_s->ahbclk_div << 1);
writel(reg_clksel, A11S_CLK_SEL_ADDR);
**
/* Program clock source and divider */
reg_clkctl = readl(A11S_CLK_CNTL_ADDR);
reg_clkctl &= ~(0xFF << (8 * src_sel));
reg_clkctl |= hunt_s->a11clk_src_sel << (4 + 8 * src_sel);
reg_clkctl |= hunt_s->a11clk_src_div << (0 + 8 * src_sel);
writel(reg_clkctl, A11S_CLK_CNTL_ADDR);
/* Program clock source selection */
reg_clksel ^= 1;
writel(reg_clksel, A11S_CLK_SEL_ADDR);
/*
* If the new clock divider is lower than the previous, then
* program the divider after switching the clock
*/
if (hunt_s->ahbclk_div < clk_div) {
reg_clksel &= ~(0x3 << 1);
reg_clksel |= (hunt_s->ahbclk_div << 1);
writel(reg_clksel, A11S_CLK_SEL_ADDR);
**
**
int acpuclk_set_rate(unsigned long rate, enum setrate_reason reason)
{
uint32_t reg_clkctl;
struct clkctl_acpu_speed *cur_s, *tgt_s, *strt_s;
int rc = 0;
unsigned int plls_enabled = 0, pll;
if (reason == SETRATE_CPUFREQ)
mutex_lock(&drv_state.lock);
strt_s = cur_s = drv_state.current_speed;
WARN_ONCE(cur_s == NULL, "acpuclk_set_rate: not initializedn");
if (cur_s == NULL) {
rc = -ENOENT;
goto out;
**
if (rate == (cur_s->a11clk_khz * 1000))
goto out;
for (tgt_s = acpu_freq_tbl; tgt_s->a11clk_khz != 0; tgt_s++) {
if (tgt_s->a11clk_khz == (rate / 1000))
break;
**
if (tgt_s->a11clk_khz == 0) {
rc = -EINVAL;
goto out;
**
/* Choose the highest speed at or below 'rate' with same PLL. */
if (reason != SETRATE_CPUFREQ
&& tgt_s->a11clk_khz < cur_s->a11clk_khz) {
while (tgt_s->pll != ACPU_PLL_TCXO && tgt_s->pll != cur_s->pll)
tgt_s--;
**
if (strt_s->pll != ACPU_PLL_TCXO)
plls_enabled |= 1 << strt_s->pll;
if (reason == SETRATE_CPUFREQ) {
if (strt_s->pll != tgt_s->pll && tgt_s->pll != ACPU_PLL_TCXO) {
rc = pc_pll_request(tgt_s->pll, 1);
if (rc < 0) {
pr_err("PLL%d enable failed (%d)n",
tgt_s->pll, rc);
goto out;
**
plls_enabled |= 1 << tgt_s->pll;
**
**
/* Need to do this when coming out of power collapse since some modem
* firmwares reset the VDD when the application processor enters power
* collapse. */
if (reason == SETRATE_CPUFREQ || reason == SETRATE_PC) {
/* Increase VDD if needed. */
if (tgt_s->vdd > cur_s->vdd) {
if ((rc = acpuclk_set_vdd_level(tgt_s->vdd)) < 0) {
printk(KERN_ERR "Unable to switch ACPU vddn");
goto out;
**
**
**
/* Set wait states for CPU inbetween frequency changes */
reg_clkctl = readl(A11S_CLK_CNTL_ADDR);
reg_clkctl |= (100 << 16); /* set WT_ST_CNT */
writel(reg_clkctl, A11S_CLK_CNTL_ADDR);
#if PERF_SWITCH_DEBUG
printk(KERN_INFO "acpuclock: Switching from ACPU rate %u -> %un",
strt_s->a11clk_khz * 1000, tgt_s->a11clk_khz * 1000);
#endif
while (cur_s != tgt_s) {
/*
* Always jump to target freq if within 256mhz, regulardless of
* PLL. If differnece is greater, use the predefinied
* steppings in the table.
*/
int d = abs((int)(cur_s->a11clk_khz - tgt_s->a11clk_khz));
if (d > drv_state.max_speed_delta_khz) {
if (tgt_s->a11clk_khz > cur_s->a11clk_khz) {
/* Step up: jump to target PLL as early as
* possible so indexing using TCXO (up[-1])
* never occurs. */
if (likely(cur_s->up[tgt_s->pll]))
cur_s = cur_s->up[tgt_s->pll];
else
cur_s = cur_s->up[cur_s->pll];
** else {
/* Step down: stay on current PLL as long as
* possible so indexing using TCXO (down[-1])
* never occurs. */
if (likely(cur_s->down[cur_s->pll]))
cur_s = cur_s->down[cur_s->pll];
else
cur_s = cur_s->down[tgt_s->pll];
**
if (cur_s == NULL) { /* This should not happen. */
pr_err("No stepping frequencies found. "
"strt_s:%u tgt_s:%un",
strt_s->a11clk_khz, tgt_s->a11clk_khz);
rc = -EINVAL;
goto out;
**
** else {
cur_s = tgt_s;
**
#if PERF_SWITCH_STEP_DEBUG
printk(KERN_DEBUG "%s: STEP khz = %u, pll = %dn",
__FUNCTION__, cur_s->a11clk_khz, cur_s->pll);
#endif
if (cur_s->pll != ACPU_PLL_TCXO
&& !(plls_enabled & (1 << cur_s->pll))) {
rc = pc_pll_request(cur_s->pll, 1);
if (rc < 0) {
pr_err("PLL%d enable failed (%d)n",
cur_s->pll, rc);
goto out;
**
plls_enabled |= 1 << cur_s->pll;
**
acpuclk_set_div(cur_s);
drv_state.current_speed = cur_s;
/* Re-adjust lpj for the new clock speed. */
loops_per_jiffy = cur_s->lpj;
udelay(drv_state.acpu_switch_time_us);
**
/* Nothing else to do for SWFI. */
if (reason == SETRATE_SWFI)
goto out;
#ifndef TEMP_76XX_ANDROID
/* Nothing else to do for power collapse. */
if (reason == SETRATE_PC)
goto out;
#endif
#ifndef TEMP_76XX_ANDROID
/*This is being compiled out by Motorola. When QCOM fixes the crash issue,
we can compile this again*/
/* Change the AXI bus frequency if we can. */
if (strt_s->axiclk_khz != tgt_s->axiclk_khz) {
rc = ebi1_clk_set_min_rate(CLKVOTE_ACPUCLK,
tgt_s->axiclk_khz * 1000);
if (rc < 0)
pr_err("Setting AXI min rate failed!n");
**
#endif /*TEMP_76XX_ANDROID*/
#ifdef TEMP_76XX_ANDROID
/* Nothing else to do for power collapse if not 7x27. */
if (reason == SETRATE_PC && !cpu_is_msm7x27())
goto out;
#endif
/* Disable PLLs we are not using anymore. */
if (tgt_s->pll != ACPU_PLL_TCXO)
plls_enabled &= ~(1 << tgt_s->pll);
for (pll = ACPU_PLL_0; pll <= ACPU_PLL_2; pll++)
if (plls_enabled & (1 << pll)) {
rc = pc_pll_request(pll, 0);
if (rc < 0) {
pr_err("PLL%d disable failed (%d)n", pll, rc);
goto out;
**
**
/* Nothing else to do for power collapse. */
if (reason == SETRATE_PC)
goto out;
/* Drop VDD level if we can. */
if (tgt_s->vdd < strt_s->vdd) {
if (acpuclk_set_vdd_level(tgt_s->vdd) < 0)
printk(KERN_ERR "acpuclock: Unable to drop ACPU vddn");
**
#if PERF_SWITCH_DEBUG
printk(KERN_DEBUG "%s: ACPU speed change completen", __FUNCTION__);
#endif
out:
if (reason == SETRATE_CPUFREQ)
mutex_unlock(&drv_state.lock);
return rc;
**
static void __init acpuclk_init(void)
{
struct clkctl_acpu_speed *speed;
uint32_t div, sel;
int rc;
/*
* Determine the rate of ACPU clock
*/
if (!(readl(A11S_CLK_SEL_ADDR) & 0x01)) { /* CLK_SEL_SRC1N0 */
/* CLK_SRC0_SEL */
sel = (readl(A11S_CLK_CNTL_ADDR) >> 12) & 0x7;
/* CLK_SRC0_DIV */
div = (readl(A11S_CLK_CNTL_ADDR) >> 8) & 0x0f;
** else {
/* CLK_SRC1_SEL */
sel = (readl(A11S_CLK_CNTL_ADDR) >> 4) & 0x07;
/* CLK_SRC1_DIV */
div = readl(A11S_CLK_CNTL_ADDR) & 0x0f;
**
for (speed = acpu_freq_tbl; speed->a11clk_khz != 0; speed++) {
if (speed->a11clk_src_sel == sel
&& (speed->a11clk_src_div == div))
break;
**
if (speed->a11clk_khz == 0) {
printk(KERN_WARNING "Warning - ACPU clock reports invalid speedn");
return;
**
drv_state.current_speed = speed;
rc = ebi1_clk_set_min_rate(CLKVOTE_ACPUCLK, speed->axiclk_khz * 1000);
if (rc < 0)
pr_err("Setting AXI min rate failed!n");
printk(KERN_INFO "ACPU running at %d KHzn", speed->a11clk_khz);
**
unsigned long acpuclk_get_rate(void)
{
WARN_ONCE(drv_state.current_speed == NULL,
"acpuclk_get_rate: not initializedn");
if (drv_state.current_speed)
return drv_state.current_speed->a11clk_khz;
else
return 0;
**
uint32_t acpuclk_get_switch_time(void)
{
return drv_state.acpu_switch_time_us;
**
/*----------------------------------------------------------------------------
* Clock driver initialization
*---------------------------------------------------------------------------*/
#define DIV2REG(n) ((n)-1)
#define REG2DIV(n) ((n)+1)
#define SLOWER_BY(div, factor) div = DIV2REG(REG2DIV(div) * factor)
static void __init acpu_freq_tbl_fixup(void)
{
unsigned long pll0_l, pll1_l, pll2_l;
int axi_160mhz = 0, axi_200mhz = 0;
struct pll_freq_tbl_map *lst;
struct clkctl_acpu_speed *t;
unsigned int pll0_needs_fixup = 0;
/* Wait for the PLLs to be initialized and then read their frequency.
*/
do {
pll0_l = readl(PLLn_L_VAL(0)) & 0x3f;
cpu_relax();
udelay(50);
** while (pll0_l == 0);
do {
pll1_l = readl(PLLn_L_VAL(1)) & 0x3f;
cpu_relax();
udelay(50);
** while (pll1_l == 0);
do {
pll2_l = readl(PLLn_L_VAL(2)) & 0x3f;
cpu_relax();
udelay(50);
** while (pll2_l == 0);
printk(KERN_INFO "L val: PLL0: %d, PLL1: %d, PLL2: %dn",
(int)pll0_l, (int)pll1_l, (int)pll2_l);
/* Some configurations run PLL0 twice as fast. Instead of having
* separate tables for this case, we simply fix up the ACPU clock
* source divider since it's a simple fix up.
*/
if (pll0_l == PLL_491_MHZ) {
pll0_l = PLL_245_MHZ;
pll0_needs_fixup = 1;
**
/* Select the right table to use. */
for (lst = acpu_freq_tbl_list; lst->tbl != 0; lst++) {
if (lst->pll0_l == pll0_l && lst->pll1_l == pll1_l
&& lst->pll2_l == pll2_l) {
acpu_freq_tbl = lst->tbl;
break;
**
**
if (acpu_freq_tbl == NULL) {
pr_crit("Unknown PLL configuration!n");
BUG();
**
/* Fix up PLL0 source divider if necessary. Also, fix up the AXI to
* the max that's supported by the board (RAM used in board).
*/
axi_160mhz = (pll0_l == PLL_960_MHZ || pll1_l == PLL_960_MHZ);
axi_200mhz = (pll2_l == PLL_1200_MHZ);
for (t = &acpu_freq_tbl[0]; t->a11clk_khz != 0; t++) {
if (pll0_needs_fixup && t->pll == ACPU_PLL_0)
SLOWER_BY(t->a11clk_src_div, 2);
if (axi_160mhz && drv_state.max_axi_khz >= 160000
&& t->ahbclk_khz > 128000)
t->axiclk_khz = 160000;
if (axi_200mhz && drv_state.max_axi_khz >= 200000
&& t->ahbclk_khz > 160000)
t->axiclk_khz = 200000;
**
t--;
drv_state.max_axi_khz = t->axiclk_khz;
/* The default 7x27 ACPU clock plan supports running the AXI bus at
* 200 MHz. So we don't classify it as Turbo mode.
*/
if (cpu_is_msm7x27())
return;
if (!axi_160mhz)
pr_info("Turbo mode not supported.n");
else if (t->axiclk_khz == 160000)
pr_info("Turbo mode supported and enabled.n");
else
pr_info("Turbo mode supported but not enabled.n");
**
/* Initalize the lpj field in the acpu_freq_tbl. */
static void __init lpj_init(void)
{
int i;
const struct clkctl_acpu_speed *base_clk = drv_state.current_speed;
for (i = 0; acpu_freq_tbl[i].a11clk_khz; i++) {
acpu_freq_tbl[i].lpj = cpufreq_scale(loops_per_jiffy,
base_clk->a11clk_khz,
acpu_freq_tbl[i].a11clk_khz);
**
**
static void __init precompute_stepping(void)
{
int i, step_idx;
#define cur_freq acpu_freq_tbl[i].a11clk_khz
#define step_freq acpu_freq_tbl[step_idx].a11clk_khz
#define cur_pll acpu_freq_tbl[i].pll
#define step_pll acpu_freq_tbl[step_idx].pll
for (i = 0; acpu_freq_tbl[i].a11clk_khz; i++) {
/* Calculate max "up" step for each destination PLL */
step_idx = i + 1;
while (step_freq && (step_freq - cur_freq)
<= drv_state.max_speed_delta_khz) {
acpu_freq_tbl[i].up[step_pll] =
&acpu_freq_tbl[step_idx];
step_idx++;
**
if (step_idx == (i + 1) && step_freq) {
pr_crit("Delta between freqs %u KHz and %u KHz is"
" too high!n", cur_freq, step_freq);
BUG();
**
/* Calculate max "down" step for each destination PLL */
step_idx = i - 1;
while (step_idx >= 0 && (cur_freq - step_freq)
<= drv_state.max_speed_delta_khz) {
acpu_freq_tbl[i].down[step_pll] =
&acpu_freq_tbl[step_idx];
step_idx--;
**
if (step_idx == (i - 1) && i > 0) {
pr_crit("Delta between freqs %u KHz and %u KHz is"
" too high!n", cur_freq, step_freq);
BUG();
**
**
**
static void __init print_acpu_freq_tbl(void)
{
struct clkctl_acpu_speed *t;
short down_idx[3];
short up_idx[3];
int i, j;
#define FREQ_IDX(freq_ptr) (freq_ptr - acpu_freq_tbl)
pr_info("Id CPU-KHz PLL DIV AHB-KHz ADIV AXI-KHz "
"D0 D1 D2 U0 U1 U2n");
t = &acpu_freq_tbl[0];
for (i = 0; t->a11clk_khz != 0; i++) {
for (j = 0; j < 3; j++) {
down_idx[j] = t->down[j] ? FREQ_IDX(t->down[j]) : -1;
up_idx[j] = t->up[j] ? FREQ_IDX(t->up[j]) : -1;
**
pr_info("%2d %7d %3d %3d %7d %4d %7d "
"%2d %2d %2d %2d %2d %2dn",
i, t->a11clk_khz, t->pll, t->a11clk_src_div + 1,
t->ahbclk_khz, t->ahbclk_div + 1, t->axiclk_khz,
down_idx[0], down_idx[1], down_idx[2],
up_idx[0], up_idx[1], up_idx[2]);
t++;
**
**
static void msm7x25_acpu_pll_hw_bug_fix(void)
{
unsigned int n;
/* The 7625 has a hardware bug and in order to select PLL2 we
* must program PLL3. Use the same table, and just fix up the
* numbers on this target. */
for (n = 0; acpu_freq_tbl[n].a11clk_khz != 0; n++)
if (acpu_freq_tbl[n].pll == ACPU_PLL_2)
acpu_freq_tbl[n].a11clk_src_sel = 3;
**
static void shared_pll_control_init(void)
{
#define PLL_REMOTE_SPINLOCK_ID 7
unsigned smem_size;
remote_spin_lock_init(&pll_lock, PLL_REMOTE_SPINLOCK_ID);
pll_control = smem_get_entry(SMEM_CLKREGIM_SOURCES, &smem_size);
if (!pll_control)
pr_err("Unable to find shared PLL control data structure!n");
/* There might be more PLLs than what the application processor knows
* about. But the index used for each PLL is guaranteed to remain the
* same. */
else if (smem_size < sizeof(struct shared_pll_control))
pr_err("Shared PLL control data structure too small!n");
else if (pll_control->version != 0xCCEE0001)
pr_err("Shared PLL control version mismatch!n");
else {
pr_info("Shared PLL control available.n");
return;
**
pll_control = NULL;
pr_err("Falling back to proc_comm PLL control.n");
**
void __init msm_acpu_clock_init(struct msm_acpu_clock_platform_data *clkdata)
{
pr_info("acpu_clock_init()n");
mutex_init(&drv_state.lock);
drv_state.acpu_switch_time_us = clkdata->acpu_switch_time_us;
drv_state.max_speed_delta_khz = clkdata->max_speed_delta_khz;
drv_state.vdd_switch_time_us = clkdata->vdd_switch_time_us;
drv_state.power_collapse_khz = clkdata->power_collapse_khz;
drv_state.wait_for_irq_khz = clkdata->wait_for_irq_khz;
drv_state.max_axi_khz = clkdata->max_axi_khz;
acpu_freq_tbl_fixup();
precompute_stepping();
acpuclk_init();
lpj_init();
print_acpu_freq_tbl();
if (cpu_is_msm7x25())
msm7x25_acpu_pll_hw_bug_fix();
if (cpu_is_msm7x27())
shared_pll_control_init();
#ifdef CONFIG_CPU_FREQ_MSM
cpufreq_table_init();
cpufreq_frequency_table_get_attr(freq_table, smp_processor_id());
#endif
** 
LinkBack URL
About LinkBacks
Itty Bitty Modder
Originally Posted by fonetek 
.
Reply With Quote
