Stuck in sunsidy lock!

[Jdgp42]

I hace recently bought a unlock code for my AT&T Backflip, I was in J_r0ds Preclair B3 and at fist went I did insert a diferen operator Sim it ask me to enter the unlock code, but I think I enter it wrong and now it doesn't show me the unlock screen, but shows me "Phone is subsidy locked. Please contact Service Proveider. Only emergency calls are allowed".

Does anyone know how to get back the screen were i can enter the unlock code?

This has anything to do with Preclai?

[nexten]

you could try reflashing. u may have to go back to flashing with the 1.5 sbf but im not sure. i havent ran across this issue

[Jdgp42]

you could try reflashing. u may have to go back to flashing with the 1.5 sbf but im not sure. i havent ran across this issue

I have tried to flash via recovery another rom but went it starts it shows me the same screen

I have read that turning on the phone and laveing it for 8 hrs it resets the screen of unlock but i have no luck with this

Any idea?

[nexten]

no u will probally have to reflash ur phone with the Original OS.

Meaning u will have to use rsd light and flash the .sbf from our firmware thread

[Jdgp42]

no u will probally have to reflash ur phone with the Original OS.

Meaning u will have to use rsd light and flash the .sbf from our firmware thread

Ok I will give it a try and post what happens! Thank you nexten!

Is strange I flash with RSD to Version: 0.13.37 that i download from firmware section here in MMM but went it starts it doesn't promt to unlock or show me the subsify screen!

Any ideas?

[nexten]

yeah u reflashed the ATT LOCKDOWN firmware . so now you will have to reroot and re load unsecured.boot.img reload recovery.img and then flash ur choice of rom back on

[Jdgp42]

yeah u reflashed the ATT LOCKDOWN firmware . so now you will have to reroot and re load unsecured.boot.img reload recovery.img and then flash ur choice of rom back on

So I root, put back the recovery, re flash to for exmaple Precalir and see if it promps the unlock code again?

[nexten]

correct. but if i were u i would make sure u enter the correct code next time

[Jdgp42]

correct. but if i were u i would make sure u enter the correct code next time

Well i did install the Preclair Beta 3 and went it did start it shows the same subsidy error screen! I will try leaving it alone for 8 hours as the say in Motorola Forums.

But dont shoult it show the same screen in the stock 1.5 at&t rom? Or ask for the unlock code?

[bestialbub]

Did you follow the usual preclair procedures and perform a FULL WIPE?

Maybe try booting w/out your sim or sdcard for funziez. That, and pulling your battery might not hurt either.

[Jdgp42]

Did you follow the usual preclair procedures and perform a FULL WIPE?

Maybe try booting w/out your sim or sdcard for funziez. That, and pulling your battery might not hurt either.

Yes I did a full wipe on the phone at first and then i just reflash it with RSD.

I have trid both and no luck, and i have tryed leaving the phone the full night without the battery and still no luck!

[httsquad325]

sorry to say buddy if its a us att moto backflip once you enter the sub code wrong 5 times that phone will stay locke to att forever i use to work for att tech support if you woulve tried 4 times and rebooted the phone you wouldve had another 5 tries but not even flashing it via rsd lite will work sorry man only thing you can do is replace the logic board

[Jdgp42]

Dammit!

[httsquad325]

ps has nothing to do with the software its sorta like a eeprom chip that stores the data its on the actual logic board

[Jdgp42]

But i have read on Motorola Suppoert Forums that it ask again for unlock code if you leave it for 8 hours on the screen of subsidy error, and tha this works on almost all motorola phones. Any idea?