Since we already had a guide on changing the slvr housing, i figured itd be in best interest to have one for changing any damn thing on the phone. Enjoy...

Removing and Replacing the Battery Cover
1. Ensure the phone is turned off.
2. Press the battery cover latch at the top of the phone, and lift the battery cover up from the phone and lift it off.



3.To replace, align the battery cover with the rear housing.
4. Place the battery cover on the rear housing and gently press the battery cover until it snaps into place. Ensure that the battery door tap is tucked in below the RF cover.

Removing and Replacing the Battery
1. Remove the battery cover as described in the procedures.
2. Lift the top end of the battery as indicated by the arrows.
3. Lift the battery up and out of the battery compartment.



4. To replace, insert the bottom of the battery into the battery compartment with contacts facing downward.
5. Press the top of the battery into the battery compartment.
6. Replace the battery cover as described in the procedures.

Removing and Replacing the SIM
1. Remove the battery cover and battery as described in the procedures.
2.Unlock the SIM holder by sliding it away from the SIM.
3. Lift up the SIM and remove it from the phone.



4. To replace, slide the SIM into the SIM holder with the notched corner located as shown.
5. Lock the SIM holder by sliding it toward the SIM.
6. Reassemble the battery and battery cover as described in the procedures.

Removing and Replacing the Antenna Cap
1. Remove the battery cover, battery and SIM, as described in the procedures.
2. Insert the disassembly tool under each side of the antenna cover to release the antenna cover latches.



3. Carefully lift the antenna cap away from the phone.
4. To replace, align the antenna cap over the antenna.
5. Place the curved edge of the antenna cap onto the phone.
6. Carefully press the straight edge of the antenna cap into place until the latches snap into place.
7. Reassemble the SIM, battery, and battery cover as described in the procedures.

Removing and Replacing the Transceiver PC Board Shield
1. Remove the battery cover, battery, SIM, and antenna, as described in the procedures.
2.Using a Torx Plus driver with a T6 bit, remove the 6 housing screws from the phone. Set the screws aside for re-use.



3. Lift the PCB shield away from the phone.



4. To replace, place the PC board shield onto the phone. Ensure the PCB and PCB shield are aligned with the chassis alignment pin.
5. Insert and tighten the 6 T6 screws to a torque setting of 14 Ncm. Do not overtighten.
6. Reassemble the antenna cap, SIM, battery and battery cover as described in
the procedures.

Removing and Replacing the Transceiver PC Board
1. Remove the battery cover, battery, SIM, and rear housing as described in the procedures..
2.Insert the flat end of the disassembly tool under the flex connector to unseat it from the transceiver PC board.



3. Use tweezers to gently unseat the coaxial cable connector from the transceiver PC board. . .



4. Use the disassembly tool to unseat the keypad PC board flex connector from its socket on the Transceiver PC board
5. Carefully lift one side of the transceiver PC board out of the phone. Be careful to avoid damage to the two flex cables and the coaxial cable.
6.Lift the transceiver PC board completely out of the phone.
7. To replace, carefully insert the side edge of the transceiver PC board into the phone chassis. Avoid damaging the battery pogo pins.
8.Carefully re-attach the the display flex connector, the main flex connector, and the coaxial cable, to the transceiver PC board. Ensure the coaxial connector is
positioned on the slot.
9.Reassemble the transceiver PC board shield, antenna cap, SIM, battery and battery cover as described in the procedures.

Removing and Replacing the Camera Assembly
1. Remove the battery cover, battery, SIM, antenna, and transceiver PC board as
described in the procedures..
2. Use the disassembly tool to unseat the camera assembly flex connector from the transceiver PC board assembly.



3. Lift the camera assembly away from the transceiver PC board.



4. Remove the rubber grommet from the camera assembly.
5. To replace, place the rubber camera assembly grommet onto the camera
assembly. Ensure the flat side of the grommet is facing away from the flex connector.
6. Align the camera assembly to the transceiver PC board.
7. Slide the camera assembly into its slot on the transceiver PC board.Ensure
that the flat side of the camera grommet lines up with the outer edge of the PC
board.
8.Carefully press the camera flex connector into its socket on the transceiver PC
board.
9. Reassemble the transceiver PC board, transceiver PC board shield, antenna cap, SIM, battery and battery cover as described in the procedures.

Removing and Replacing the Front Housing
1. Remove the battery cover, battery, SIM, antenna, and transceiver PC board as described in the procedures.
2. Insert the disassembly between the front housing and the chassis assembly.



3. Slide the disassembly tool around the phone between the front housing and the phone to release the housing catches along the sides of the front housing.
4. Carefully lift and remove the front housing from the phone.
5. To replace, align the front housing to the phone.
6. Lower the phone onto the front housing and keypad.
7. Carefully and gently press the front housing into the chassis until all of the housing catches are engaged.
8. Reassemble the transceiver PC board, transceiver PC board shield, antenna cap, SIM, battery and battery cover as described in the procedures.

Removing and Replacing the Keypad
1. Remove the battery cover, battery, SIM, rear housing, and transceiver PC board, as described in the procedures.
2.Lift the keypad up from one corner as shown in Figure 16 and remove it from the front housing.



3.To replace, align the keypad holes with the front housing pins and place the keypad onto the front housing.
4. Reassemble the front housing, transceiver PC board, transceiver PC board shield, antenna cap, SIM, battery and battery cover as described in the procedures.

Removing and Replacing the Keypad PC Board
1. Remove the battery cover, battery, SIM, antenna, transceiver PC board, and front housing, as described in the procedures.
2. Use the Torx driver with a T3 bit to remove the 2 screws from the Keypad PC board.



3. Rotate the end of the PC board up and disconnect the flex connector underneath the keypad PC board.



4. Use the coaxial cable extraction tool to disconnect the coaxial cable connector from the PC board and move the coaxial cable away from the PC board.
5. Remove the silver colored chassis seal.
6. Remove the flex from the chassis
7.Left the keypad PC board away from the phone.
8. To replace, align the flex connector the keypad PC board and gently press the connector until properly seated in the connector socket.
9. Thread the coaxial cable around the cable guide and seat the connector onto its socket on the keypad PC board.
10. Insert and tighten the 2 T3 screws.
11. Paste on the silver chassis seal
12. Reassemble the front housing, transceiver PC board, transceiver PC board shield, antenna cap, SIM, battery and battery cover as described in the procedures.

Removing and Replacing the Antenna
1. Remove the battery cover, battery and SIM, as described in the procedures.
2. Use the plastic tweezers to lift the antenna assembly out of the phone.



3. Carefully remove the antenna from the phone.
4. To replace, insert the antenna into the antenna slot on the phone. Ensure the antenna makes contact with the RF contacts on the PC board.
5. Reassemble the keypad PC board, keypad, front housing, transceiver PC board, transceiver PC board shield, antenna cap, SIM, battery and battery cover as described in the procedures.

Removing and Replacing the Display Module
1. Remove the battery cover, battery, rear housing, and transceiver PC board as described in the procedures.
2. Turn over the chassis assembly and use the metal tweezers to release the six display bracket latches located under the chassis assembly.



3. Turn the chassis assembly over and lift the top edge of the display module.



4.Carefully thread the display flex cable through the slot in the chassis assembly and lift the display module away from the chassis.
5.To replace, align the display module to the chassis assembly.
6. Hold the side of the display module near the flex cable away from the chassis assembly.
7. Carefully thread the display flex connector through the opening on the chassis assembly.
8. Lower the display module fully onto the chassis assembly and gently press it into place.

THE PARTS:
Display Module
Antenna
Keypad PC Board
Keypad
Front Housing
Transceiver
PC Board
Transceiver PC Board Shield
Antenna Cap
SIM
Battery
Battery Cover